Geotechnical Report Cost in Melbourne: What You'll Pay


For most Melbourne homes, a standard soil test (a site classification) costs roughly $450 to $900 plus GST. A full geotechnical investigation for a basement, a pool, a sloping block or a site with deep fill usually starts around $1,500 and can pass $3,000 to $6,000. The fee is small next to what it protects. The soil class decides how deep and how strong your footings need to be, and footings are where a build budget most often blows out. We are Yorcon, a Melbourne builder, and this is how we would explain it to a friend about to start an extension or a new home.
TL;DR
A standard AS 2870 soil test on a typical Melbourne block is commonly quoted at about $450 to $900 plus GST in 2026 price lists, with $500 to $800 plus GST the most common band.
Extra boreholes, footing probes for upper-storey additions, deeper drilling, lab shrink-swell testing and travel outside metro Melbourne are usually quoted on top.
Detailed investigations for basements, pools, landslip-prone or filled sites start higher, often $1,500 to $3,000 and up to $6,000 or more.
The test fee is not the number that matters most. The soil class sets your footing design, which can swing the build cost by tens of thousands of dollars.
Get the report before you sign a building contract, so the price you sign reflects your actual ground.
Table of Contents
What a geotechnical report actually is
A geotechnical report is a written assessment of the ground under your home, prepared by a geotechnical engineer or a firm working under one. A drill rig or hand auger takes samples from the site. The samples are described and, where needed, tested in a laboratory for moisture content, plasticity and how much the clay swells and shrinks.
The key output for a house is the site classification under AS 2870, the Australian Standard for residential slabs and footings. It sorts sites into classes:
A: stable, almost no movement
S: slightly reactive
M: moderately reactive
H1 and H2: highly reactive clay
E: extremely reactive
P: a “problem” site, such as deep fill or soft soil, that needs specific engineering
The class tells the engineer how much the ground is likely to move as it wets and dries. That movement determines your footing type, stump depth and slab thickness.
People use three names for roughly the same thing: soil test, site classification and geotechnical report. In everyday Melbourne use, a “soil test” is the basic version. A “geotechnical investigation” is the deeper one, with more boreholes and engineering advice.
What you can expect to pay in Melbourne
Melbourne soil testing firms publish their pricing openly, and the 2026 figures line up well. Here is the pattern across the price lists we reviewed.
Type of work | Typical price range (2026 published pricing) |
Basic site classification, standard residential lot | $450 to $900 plus GST, most often $500 to $800 |
Footing probes for extensions or upper-storey additions | Roughly $150 to $600 per probe, depending on the firm |
Site classification with footing design advice | About $1,200 to $2,500 |
Full geotechnical investigation (basement, pool, complex site) | $1,500 to $3,000 and up, commonly $3,000 to $6,000 |
Erosion Management Overlay or landslip investigations | Typically $3,000 to $6,000 or more |
Disputed or highly complex sites | $3,000 to $10,000 or more |
A few firms quote higher flat ranges for residential work, such as $1,800 to $3,500 depending on site size, access and soil complexity. Others advertise fixed fees near $450 plus GST for metro sites, with a signed AS 2870 report and footing recommendations included. So the spread is real, and it mostly comes down to what is in the scope.
Two habits will keep you from comparing the wrong numbers:
Check whether GST is included. A “$495 + GST” fee is $544.50 once GST is added.
Check what the base price covers. The cheapest figure often assumes an eligible standard site, a set number of boreholes and no lab work.
These are published ranges for the period, not a quote. Fees move with rig availability, travel and lab costs, so treat them as a way to judge whether a quote is sensible rather than a fixed rate.
What pushes a quote up
Geotechnical pricing is built from a handful of line items. Knowing them helps you read a quote properly.
Number and depth of boreholes
A standard residential test commonly drills one to three holes to about 1.5 to 1.8 metres. Larger footprints, townhouse developments and sites where the ground varies need more holes. Basements and deep piers need much deeper drilling, which is a different job and a different price.
Footing probes for extensions
If you are adding an upper storey, the existing footings carry new load. Engineers often probe the existing footings to see what is there, and that is usually charged per probe. It is a normal add-on, not a sign of padding.
Fill and unusual ground
Where a block has been filled, a simple classification can become a deeper investigation. Deep fill may need drilling beyond the standard depth, charged per metre. A good firm will tell you and get your approval before going deeper, so you are never surprised on the invoice.
Laboratory testing
Melbourne’s basalt clays, particularly west and north of the city, can vary a lot in how much they shrink and swell, even within one mapped area. That is why lab testing appears in Melbourne quotes more often than in some other cities. If your block sits on basalt clay and the quote has no lab allowance at all, it is fair to ask why.

Access and location
Tight rear access, existing buildings, underground services and sloping land all slow the work. Sites outside metro Melbourne, roughly beyond 45 km from the CBD, generally attract a travel allowance.
Council or overlay requirements
Some properties sit under an Erosion Management Overlay, a slope stability requirement or other planning conditions that call for specific testing. If you know about any of these, say so when you ask for a quote, so the scope is right the first time.
Why the soil class matters more than the fee
The test fee is a few hundred dollars. The footing design it triggers is a different order of money.
Melbourne’s western and northern growth corridors, including Werribee, Tarneit, Truganina, Melton, Craigieburn and Sunbury, sit on weathered basalt that produces highly reactive clay, commonly classed H1 or H2 and in pockets E. Many south-eastern sandbelt sites, from Cheltenham towards Frankston, are more often stable A or S, with simpler footings. One Melbourne guide estimates a reactive site can add something like $15,000 to $50,000 to foundation costs compared with a stable one. Treat that as an indication only: your engineer’s design and your builder’s price are what count.
The real risk is not paying for the test. It is skipping it, or leaving it until after you have signed. A contract priced on an assumed soil class can turn into a variation of $20,000 to $40,000 when the slab-stage engineering comes back with a different answer. We cover that trap in more detail in our Melbourne site costs checklist.
If you have ever seen a quote with a low “site costs” provisional sum and no soil report behind it, you have seen how this happens. A provisional sum is a placeholder allowance. Without ground data it is a guess, and the guess usually lands on you.

How the report gets used in your project
For a home extension or renovation costing more than $10,000, Consumer Affairs Victoria’s guidance says the builder must obtain a soil report and foundation data to design the footings and give an adequate cost estimate. The foundation data feeds directly into stump depth and whether you need a slab or strip footings.
For new dwellings, councils and building surveyors generally expect a soil investigation report to support the building permit. For additions and alterations, whether one is required can depend on the building surveyor, so it is worth confirming early. Our guide to building permits in Melbourne explains where the soil report sits in the approvals sequence.
In practice the report flows into three places:
The structural engineer’s footing design, which sets the depth, width and reinforcement of footings and slabs.
The building permit application, where the surveyor wants to see the design is based on the actual ground.
Your fixed price, because the foundation cost can only be firm once the soil class is known.
That last point is why we want the soil data early on a project. It lets a price mean something.
Getting an accurate quote
Soil testing firms usually need very little from you to prepare a formal fee proposal:
The site address.
Plans of the proposed work, or a short description of what you intend to build.
Any planning overlays or permit conditions that mention soil, salinity, slope stability or similar testing.
Notes on access, such as a narrow side path, a locked gate or a steep rear yard.
Then ask the firm to put these in writing, so you can compare quotes properly:
How many boreholes are included, and to what depth.
Whether laboratory shrink-swell testing is included.
What it costs to drill deeper if fill or rock is found.
Whether footing probes are included or extra.
What the deliverable is, for example a signed AS 2870 site classification with footing recommendations.
Travel charges, GST and turnaround.
A quote that states the method, depth, tests, exclusions and turnaround is one you can compare like for like.
How long it takes
The fieldwork is quick. Many standard residential soil tests are done on site in between half an hour and a couple of hours, and a standard block may need a day or two of drilling. Fieldwork is often booked within a week or so of accepting the quote.
Reports then take a few working days for a standard classification, longer if lab testing is needed. Published turnarounds for metro Melbourne run from a few business days up to around two weeks for a typical site, and several weeks for townhouse developments or complex investigations. Basements, landslip or contaminated sites can take far longer.
Reports have no fixed expiry, but the convention is two to three years, and some councils want a re-inspection letter on older ones. If you bought a block with an old report, check its age before you rely on it.
Timing: before you buy, before you sign
If you are still choosing a block, a soil test or a look at any existing geotechnical data before you buy can change your budget before you are committed. If you already own the land, get the report before you sign a building contract.
In both cases, the aim is the same: your builder prices the footings on real ground information, not an assumption. That is how you avoid the slab-stage surprise.
If your block has drainage or flooding concerns, it is also worth thinking about what happens to the ground around the house, not just under it. How a surface is built up and drained matters, and this explanation of a flood resistant driveway subbase shows the principle clearly. For the Melbourne rules that apply to runoff from your own block, see our stormwater requirements guide.
When the soil report points to bigger costs
Sometimes the report tells you something you would rather not hear: reactive clay, fill, or movement in existing footings. That is still useful, because you learn it while you can plan for it.
For existing homes with signs of movement, such as cracking, sticking doors or sloping floors, the engineer may recommend repairs before building. Our guide to underpinning costs in Melbourne and our overview of structural renovation costs and permits show what those conversations look like. If you want a wider view of what the test fee sits alongside, we also break down what homeowners can expect to pay for a soil test.
Working with a builder who manages the whole job
The report is only the first document in a long chain: design, engineering, permits, approvals, then construction. We manage that whole chain for Melbourne homeowners, from design through to completion, with clear communication at each stage. For you, that means the soil result is not a loose piece of paper. It informs the design, the engineering, the permit and the price in one connected process.
Our Home Extensions and Design & Build services are built around exactly that approach. If you are weighing up a project and want to talk through how ground conditions might shape your budget, book a free project feasibility call and we will go through it with you.

FAQ
What is the average cost of a geotechnical report in Melbourne?
For a typical residential block, a basic soil test and site classification usually costs $450 to $900 plus GST in 2026 pricing, with $500 to $800 plus GST the most common range. Full investigations for basements, pools or complex sites typically start from about $1,500 and often reach $3,000 to $6,000.
Do I need a soil test for a home extension?
Often yes. For extensions and renovations over $10,000, Consumer Affairs Victoria’s guidance says the builder must obtain a soil report and foundation data to design the footings and estimate accurately. Whether your building surveyor also requires one for the permit can vary, so confirm it early.
Why do some quotes cost so much more than others?
Usually the scope differs. A lower price may cover only two or three shallow boreholes, while a higher one may include lab testing, deeper drilling, footing design and a longer report. Compare boreholes, depth, lab testing, exclusions and GST before comparing totals.
How long does a soil test take?
On-site work for a standard block usually takes from under an hour to a day or two. The signed report commonly follows within a few business days to about two weeks, depending on whether lab testing is needed. Complex sites take longer.
Can the soil class change my building cost?
Yes. The class sets the footing and slab design. Highly reactive clay, common on basalt in Melbourne’s west and north, can add tens of thousands of dollars to foundations compared with a stable site, which is why the report should come before you sign a contract.
Sources
Recommended









